.jpg)
.jpg)
A year, it seems, is a long time in the world of Star Wars MOCs; Cavegod (Pete) has teased me mercilessly about my slow rate of progress, and fellow AT-AT builder Morten has also recently started to wind me up about the time it's taking, while texting me pictures of his amazing UCS Nebulon B Frigate which he's also managed to finish in the time it's taken me to not-yet-finish the AT-AT....
The final remaining section is the right side of the body; I think I dragged my heels even more than usual recently because I struggled so much building the left side. Thing is, I do actually have a deadline for finishing the AT-AT - October of this year, of which more in a future posting - so I figured that I really needed to pull my finger out and get on with it. With this in mind, I booted up LDD and loaded up the last remaining LDD file (picture below - click to enlarge).
.jpg)
As discussed at length in my previous AT-AT posting, brick outlines are at last once again visible for me on LDD after an extended period of them being greyed out in the menu and inaccessible; it makes following the building guide one hell of a lot easier. As you can see in the bottom left-hand corner of the picture, the right side of the body consists of a total of 722 pieces, which is a dead giveaway that it isn't just a mirror image of the 720 piece left side.
As you might expect with something of this size, generating the building guide (which thankfully only requires a single click of the green and yellow button visible on the top right of the screengrab above) takes a couple of minutes. Interestingly, the building guide for the left side of the AT-AT body split the build into front, mid, rear and lower sections. The guide for the right side just dives straight in to the mid-section, however, and then literally continues the build into the rear and lower sections as you can see in the example page from the building guide below; only the front section is built separately and attached in the final step. There's really no good reason for this difference in approach, but then I've long since given up trying to understand the eccentricities of the LDD building guide generator - it's a law unto itself, and I suspect that any attempt to second guess anything it does would be futile.
.jpg)
As some of you will recall, I had massive problems with the left side of the AT-AT body, specifically attaching the front and rear sections to the larger mid-section. This was mainly because the sub-assemblies which join the sections together - basically a whole bunch of 2 x 3 slopes mounted on a couple of long plates - were warped and therefore struggled to bear any weight. Anyway, I think I figured out the cause of the warping.... Below (click to enlarge) you can see a picture of two 2 x 3 slopes placed upside down and side by side. The slope on the left is from the batch that I used to build the left side of the body; if you look closely at the two anti-studs on the underside you can see that their walls are thickened in some areas. The slope on the right is from a new batch that I bought when I got suspicious that there was a problem with the slopes I'd used for the left side; here the anti-studs don't have corresponding areas of thickening on their walls. I used the new batch of slopes to build the right side of the body and the warping issue was far less evident. I'm not sure if the slope on the left is from a faulty batch, or if it's a normal variant - if any readers can shed any light on this then please post a comment or drop me an e-mail. I'm pretty sure however that this 'feature' was at the root of my problems, and I'll swap out the faulty (?) slopes from the left side too when I get a chance.
Having identified the above problem in advance of getting started on the right side of the body, construction turned out to be reasonably straightforward, and was accomplished in just a few hours spread over 3 evenings. The front section was a bit unstable and needed some simple modification to stiffen it up a bit, but otherwise everything came together with relatively little fuss, and you can see the end result below (click to enlarge).
.jpg)
Taking a close look at the picture above, I can see that some of the joins between the various sections aren't as tight as they might be, but that should be fairly easily remedied with a bit of (carefully applied) pressure in appropriate areas; the fact that I was reluctant to apply much in the way of brute force to push all the sections together is a reflection of my bad previous experiences with the left side of the body when the application of just a little too much pressure in the wrong place was enough to break the blasted thing into many pieces....
As previously stated, the two sides of the AT-AT aren't symmetrical. Both the front and rear sections below (click to enlarge) are slightly diffferent from their counterparts on the left side of the body. Anyone out there with time on their hands can therefore feel free to play a game of "AT-AT spot the difference" should they so desire, although if that's you then you might want to consider getting out more.
.jpg)
.jpg)
One thing of note on the rear section above is the flash of blue visible in the upper left quadrant. This is down to a couple of blue Technic half pins. I really need to ask Pete whether this is intentional, or whether something's supposed to be attached to them; in the event that they're actually supposed to look that way I'll replace them with the equivalent parts in bley.
So that's it, then - all sections completed, and 6215 pieces used by my best estimate (plus a few extras to provide a little additional stability in places). Which means that all that should be left for me to do is the small matter of joining all the completed sections together into the finished AT-AT - not long to wait now !
< -- Building the AT-AT : Part 9 Building the AT-AT : Part 11 -- >